Major service - motor grader (all makes)
Estimated duration: 6 - 10 hours • Frequency: every 1,000 engine hours
Equipment Details
| # | Service Action | Type | Done | Notes |
|---|---|---|---|---|
| Engine (additional to 500-hour) | ||||
| 1 | Replace inner air filter element | REPLACE | ☐ | |
| 2 | Check/clean injectors or send for testing | INSPECT | ☐ | |
| 3 | Inspect turbocharger for play and oil leaks | INSPECT | ☐ | |
| 4 | Inspect exhaust manifold and gaskets | INSPECT | ☐ | |
| Hydraulic System (additional to 500-hour) | ||||
| 5 | Drain and replace full hydraulic oil (ISO VG 46) | DRAIN/FILL | ☐ | |
| 6 | Replace hydraulic suction strainer | REPLACE | ☐ | |
| 7 | Inspect hydraulic pump for noise/pressure/wear | INSPECT | ☐ | |
| 8 | Test all implement and steering relief pressures | TEST | ☐ | |
| Drivetrain (additional to 500-hour) | ||||
| 9 | Drain and replace tandem drive case oil (all cases) | DRAIN/FILL | ☐ | |
| 10 | Drain and replace transmission oil | DRAIN/FILL | ☐ | |
| 11 | Check torque converter stall speed and shift quality | TEST | ☐ | |
| Circle Drive (additional to 500-hour) | ||||
| 12 | Drain and refill circle drive gearbox oil | DRAIN/FILL | ☐ | |
| 13 | Inspect circle rail for wear and scoring | INSPECT | ☐ | |
| 14 | Check pinion engagement, backlash and circle shoes | MEASURE | ☐ | |
| Cooling System (additional to 500-hour) | ||||
| 15 | Drain, flush and replace coolant (50/50 EG) | FLUSH/FILL | ☐ | |
| 16 | Pressure test cooling system | TEST | ☐ | |
| 17 | Replace thermostat (if due per manufacturer) | REPLACE | ☐ | |
| Structural and Blade (additional to 500-hour) | ||||
| 18 | Inspect mainframe, drawbar, A-frame and circle support welds | INSPECT | ☐ | |
| 19 | Measure moldboard cutting edge and end bit wear | MEASURE | ☐ | |
| 20 | Check all drawbar and circle pivot pins and bushes | INSPECT | ☐ | |
| Brakes and Steering (additional to 500-hour) | ||||
| 21 | Measure brake disc/pad wear against specifications | MEASURE | ☐ | |
| 22 | Test service brake and park brake operation | TEST | ☐ | |
| 23 | Inspect articulation steering cylinders and linkage | INSPECT | ☐ | |
Fluid Specifications (General Guide)
| System | Type / Grade | Approx. Capacity |
|---|---|---|
| Engine oil | 15W-40 CI-4 / CK-4 | 20 - 30 L |
| Hydraulic oil | ISO VG 46 (AW 46) | 100 - 200 L (full change) |
| Coolant | 50/50 ethylene glycol | 25 - 40 L (full system) |
| Tandem drive oil | SAE 60 or manufacturer spec | 8 - 15 L per case |
| Transmission oil | TO-4 or manufacturer spec | 30 - 50 L |
| Circle drive gearbox | 80W-90 GL-5 or SAE 30 | 3 - 6 L |
| Grease | EP2 lithium complex | As required |
Specifications are general guidelines for typical motor graders. Always refer to the manufacturer's service manual for your specific make and model. Capacities vary by machine size. At the 1,000-hour interval, hydraulic oil, coolant, tandem drive oil, transmission oil and circle gearbox oil are fully drained and replaced.
Parts / Consumables Required (1000-hour additional items)
| # | Part / Consumable | Part Number | Qty | Ready |
|---|---|---|---|---|
| 1 | Engine oil (15W-40) | 20-30 L | ☐ | |
| 2 | Engine oil filter | 1 | ☐ | |
| 3 | Inner air filter element | 1 | ☐ | |
| 4 | Outer air filter element | 1 | ☐ | |
| 5 | Fuel filter element | 1 | ☐ | |
| 6 | Hydraulic return filter | 1 | ☐ | |
| 7 | Hydraulic suction strainer | 1 | ☐ | |
| 8 | Hydraulic oil (ISO VG 46) | 100-200 L | ☐ | |
| 9 | Tandem drive oil (SAE 60) | 24-60 L | ☐ | |
| 10 | Transmission oil (TO-4) | 30-50 L | ☐ | |
| 11 | Circle gearbox oil (80W-90) | 3-6 L | ☐ | |
| 12 | Coolant (pre-mixed or concentrate) | 25-40 L | ☐ | |
| 13 | Thermostat (if replacing) | 1 | ☐ | |
| 14 | EP2 grease cartridges | 4-6 | ☐ | |
| 15 | Rags, drip trays, waste oil containers | - | ☐ |
Notes / Defects Identified
Next Service Due
Technician
Supervisor / Workshop Manager